Purpose of TDM over Packet technology

Telecom companies and enterprise users can save network and equipment cost and generate additional revenue by offering different types of services over a single packet-switched infrastructure by the use of E1oP equipment. The E1oP equipment is also suitable for connecting to Ethernet / packet wireless equipment to achieve fast deployment of E1 services over wireless Ethernet networks. One particular application is to build E1 links with low cost Wireless LAN bridges, replacing expensive TDM / E1 microwave radios. The 16 x E1 over Ethernet (VCL-E1oP) multiplexer may be used to provide legacy TDM services over Gigabit Ethernet optical fiber, or wireless Ethernet/IP networks.

How the TDM over Packet (16 E1 Port GE Version) equipment works?

The E1 data streams received on the E1 interfaces are converted by the E1oP engine of the E1oP equipment to Ethernet data packets (of a fixed size) and transported over the Ethernet network with UDP / IP, MEF or MPLS headers. At the receiving end the E1oP reconstructs the original data streams by removing the IP, MEF or MPLS headers and converts the Ethernet data packets back to E1 frames using highly reliable and accurate clock recovery mechanism. The 'VCL-E1oP' (16 E1 port GE Version) offers the user a choice of standard, E1 to packet and packet to E1 conversion mechanisms that include SAToP and CESoPSN technologies.

E1 and E1oP Interface

• Supports 16 independent E1 interfaces.
• Circuit emulation platform that migrates existing TDM based legacy services to a next-generation network.
• Supported standard TDM over IP RFCs:
• RFC 5086 - Structure-Aware Time Division Multiplexed (TDM) Circuit Emulation Service over Packet Switched Network (CESoPSN) (12/2007)
• RFC 5087 - Time Division Multiplexing over IP (TDMoIP) (12/2007)
• RFC 4553 - Structure-Agnostic Time Division Multiplexing (TDM) over Packet (SAToP) (06/2006)
• Clock options: Internal, External, Adaptive, Recovered clock and Asymmetrical (One-Clock and Two-Clock) options for the E1 TDM port synchronization. Automatic clock priority selection with fall back.
• Supports CESoPSN payload mechanism to support the fractional E1 with data rate of 64Kbps to 2.048Mbps (DS0 timeslot level). User configurable data rate from 64kbps to 2048kbps, in steps of 64kbps.
• CESoPSN payload mechanism feature allows the user to optimize the packet switched network by limiting its usage to the corresponding number of time slots carried by an E1 channel.
• Supports SAToP payload mechanism to transport full E1 (transparent to the structure of the TDM frame useful for transporting framed / unframed E1 channels).
• Supports IETF-PWE3 (pseudo-wire), SAToP and CESoPSN transport mechanisms.
• Supports IP, MPLS and MEF8 (Metro Ethernet) tagging.
• Supports three E1 framing modes - Framed, Unframed and Multi-Framed with CAS signaling.
• Supports point-to-point, point-to-multipoint and drop and insert applications.
• Supports network latency / packet delay variation / jitter buffer of up to 512ms.
• Absolute and Differential timestamps.
• Jitter and Wander conforms to G.823 / G.824 and G.8261 and TDM specifications.
• RJ45 - 120 ohms balanced E1 interfaces. Optional 75 Ohms BNC interface (120 Ohms to 75 Ohms interface converter cables provided).
• E1 Local and Remote Loop-back (RLOOP) facility for testing and diagnostics.

Ethernet / IP Network Interface

• Switching Capacity upto 6 Gbps, non-blocking
• 4 GigE Ports.
• Optical SFP based (1000Base-FX) and Electrical (10/100/1000Base-T) Ethernet port options.
• 4 x 10/100/1000BaseT Copper Ports.
• 4 x 1000BaseFX Optical Fiber Ports. (may use a combination / mix of any 4 Copper or Fiber Ports)
• Point-to-point and point-to-multipoint applications based on IP addressing.
• Supports drop and insert applications.
• Port Control Ingress Rate Limiting.
• 1+1 Ethernet link redundancy
• Rapid Spanning Tree Protocol.
• Ethernet Port Trunking.
• User configurable MTU (T1oP payload) packet size up to 1800 Bytes.
• Configurable payload size for each bundle.
• Switch supports jumbo frame sizes of up to 9000 Bytes.
• Supports 802.1Q based QoS, 802.1p based packet priority.
• Port Based Priority (Classifying Services).
• DSCP and 802.1Q / 802.1p based packet tagging and prioritization.
• Flow Control in an Ethernet Packet Networks (Regulating Traffic).
• Port / Customer based bandwidth allocation (Port Rate Limiting).
• MPLS, MEF and UDP tagging for Ethernet traffic.
• Separate IP Address for TDM traffic and equipment management.
• VLAN tagging for TDM traffic and equipment access / management.
• Single / Double 802.1 VLAN tagging (Q in Q VLAN Tagging) - User configurable.
• UDP-specific “Special” Ethernet type.
• In band VCCV ARP.
• Broadcast DA.

Few Key Features Explained

• Port Based Priority (Classifying Services) - Port based Priority feature allows the user to assign priority to the individual Ethernet ports, so that traffic can be regulated according to the port on which that service is connected. The user may also assign highest priority to TDM (E1/E3) traffic and Ethernet services on a lower priority.
• VLAN Based Priority (Classifying Services) - VLAN based Priority feature allows the user to assign priorities to different VLANs carrying various types of services / traffic according based on user categories and preferences. The user may assign highest priority to TDM (E1/E3) traffic and Ethernet services on a lower priority. User may also configure which TDM link should be given preference over the other TDM links when the uplink bandwidth falls below a particular threshold.
• Flow Control in an Ethernet Packet Networks (Regulating Traffic) - Flow Control feature allows the user to regulate Ethernet traffic flow to minimize packet loss due to data bursts.
• Port / Customer based bandwidth allocation (Port Rate Limiting) - Port based Ingress Ethernet Rate Limiting allows the user to assign the bandwidth as per port / service requirements, in addition to provisioning traffic by using 802.1Q and 802.1p VLANs and packet priority.

System Management, Monitoring and Alarm Interfaces

• NMS (Network Management System) to monitor multiple units from single Central Location.
• External Alarm - Dry contact relay alarms are also available at rear of the system to connect the system to an external alarm.
• Supports system temperature monitoring with High Temperature threshold and Low Temperature threshold alarms and SNMP Traps.
• Supports SNMP V2 Monitoring and Traps.
• Self-test for checking system errors upon system boot-up.
• Event Logging.
• Clock Performance Alarms.
• Network Performance Alarms.
• Network Performance Monitoring and Diagnostics.
• Online / remote upgrade of firmware.